Facile Lithium Densification Kinetics by Hyperporous/Hybrid Conductor for High-Energy-Density Lithium Metal Batteries.

Lithium metal anode (LMA) emerges as a promising candidate for lithium (Li)-based battery chemistries with high-energy-density. However, inhomogeneous charge distribution from the unbalanced ion/electron transport causes dendritic Li deposition, leading to "dead Li" and parasitic reactions, particularly at high Li utilization ratios (low negative/positive ratios in full cells). Herein, an innovative LMA structural model deploying a hyperporous/hybrid conductive architecture is proposed on single-walled carbon nanotube film (HCA/C), fabricated through a nonsolvent induced phase separation process. This design integrates ionic polymers with conductive carbon, offering a substantial improvement over traditional metal current collectors by reducing the weight of LMA and enabling high-energy-density batteries. The HCA/C promotes uniform lithium deposition even under rapid charging (up to 5 mA cm-2) owing to its efficient mixed ion/electron conduction pathways. Thus, the HCA/C demonstrates stable cycling for 200 cycles with a low negative/positive ratio of 1.0 when paired with a LiNi0.8Co0.1Mn0.1O2 cathode (areal capacity of 5.0 mAh cm-2). Furthermore, a stacked pouch-type full cell using HCA/C realizes a high energy density of 344 Wh kg-1 cell/951 Wh L-1 cell based on the total mass of the cell, exceeding previously reported pouch-type full cells. This work paves the way for LMA development in high-energy-density Li metal batteries.

Mitigating Gas Evolution in Electron Beam-Induced Gel Polymer Electrolytes Through Bi-Functional Cross-Linkable Additives.

The current high-capacity lithium-ion batteries (LIBs), reliant on flammable liquid electrolytes (LEs) and nickel-rich cathodes, are plagued by safety hazards, especially the risk of hazardous gas release stemming from internal side reactions. To address these safety concerns, an electron beam (E-beam)-induced gel polymer electrolyte (E-Gel) is introduced, employing dipentaerythritol hexaacrylate (DPH) as a bi-functional cross-linkable additive (CIA). The dual roles of DPH are exploited through a strategically designed E-beam irradiation process. Applying E-beam irradiation on the pre-cycled cells allows DPH to function as an additive during the initial cycle, establishing a protective layer on the surface of the anode and cathode and as a cross-linker during the E-beam irradiation step, forming a polymer framework. The prepared E-Gel with CIA has superior interfacial compatibility, facilitating lithium-ion diffusion at the electrode/E-Gel interface. The electrochemical assessment of 1.2 Ah pouch cells demonstrates that E-Gel substantially reduces gas release by 2.5 times compared to commercial LEs during the initial formation stage and ensures superior reversible capacity retention even after prolonged cycling at 55 °C. The research underscores the synergy of bifunctional CIA with E-beam technology, paving the way for large-scale production of safe, high-capacity, and commercially viable LIBs.

Tailoring Three-Dimensional Cross-Linked Networks Based on Water-Soluble Polymeric Materials for Stable Silicon Anode.

For stable battery operation of silicon (Si)-based anodes, utilizing cross-linked three-dimensional (3D) network binders has emerged as an effective strategy to mitigate significant volume fluctuations of Si particles. In the design of cross-linked network binders, careful selection of appropriate cross-linking agents is crucial to maintaining a balance between the robustness and functionality of the network. Herein, we strategically design and optimize a 3D cross-linked network binder through a comprehensive analysis of cross-linking agents. The proposed network is composed of poly(vinyl alcohol) grafted poly(acrylic acid) (PVA-g-PAA, PVgA) and aromatic diamines. PVgA is chosen as the polymer backbone owing to its high flexibility and facile synthesis using an ecofriendly water solvent. Subsequently, an aromatic diamine is employed as a cross-linker to construct a robust amide network that features a resonance-stabilized high modulus and enhanced adhesion. Comparative investigations of three cross-linkers, 2,2'-bis(trifluoromethyl)benzidine, 3,3'-oxidianiline, and 4,4'-oxybis[3-(trifluoromethyl)aniline] (TFODA), highlight the roles of the trifluoromethyl group (-CF3) and the ether linkage. Consequently, PVgA cross-linked with TFODA (PVgA-TFODA), featuring both -CF3 and -O-, establishes a well-balanced 3D network characterized by heightened elasticity and improved binding forces. The optimized Si and SiOx/graphite composite electrodes with the PVgA-TFODA binder demonstrate impressive structural stability and stable cycling. This study offers a novel perspective on designing cross-linked network binders, showcasing the benefits of a multidimensional approach considering chemical and physical interactions.

Promoting Homogeneous Zinc-Ion Transfer Through Preferential Ion Coordination Effect in Gel Electrolyte for Stable Zinc Metal Batteries.

Aqueous zinc metal batteries (AZMBs) are emerging energy storage systems that are poised to replace conventional lithium-ion batteries owing to their intrinsic safety, facile manufacturing process, economic benefits, and superior ionic conductivity. However, the issues of inferior anode reversibility and dendritic plating during operation remain challenging for the practical use of AZMBs. Herein, a gel electrolyte based on zwitterionic poly(sulfobetaine methacrylate) (poly(SBMA)) dissolved with different concentrations of ZnSO4 is proposed. Two-dimensional correlation spectroscopy based on Raman analysis reveals an enhanced interaction priority between the polar groups in SBMA and the dissolved ions as electrolyte concentration increases, which establishes a robust interaction and renders homogeneous ion distribution. Attributable to the modified coordination, zwitterionic gel polymer electrolyte with 5 mol kg-1 of ZnSO4 (ZGPE-5) facilitates stable zinc deposition and improves anode reversibility. By taking advantage of preferential coordination, a symmetrical cell evaluation employing ZGPE-5 demonstrates a cycle life over 3600 h, where ZGPE-5 also exerts a beneficial effect on the full cell cycling when assembled with Zn0.25 V2 O5 cathode. This study elucidates changes in the internal ion behavior that are dependent on electrolyte concentrations and pave the way for durable AZMBs.